Hard cocking and POI shift FIX!!!

Benjamin Marauder Troubleshooting
Forum rules
MarauderAirRifle.com is not owned, Affiliated, or controlled by Crosman.
The Scope and goal of this section of the form is provide useful information 24/7 because I realize that most of us play with the toys on weekends when big companies and telephone support is not always available.

Normally if problems occur during this window you are SOL until the next business day (and your fun is over)

So if you are having problems check or search here to see if it is a known issue and what steps can be taken to resolve the issue.

If you ask questions on this forum, I can not guarantee Crosman support will see the post or reply to it, and you may need to give them a call at 800-724-7486 if you still need help or replacement parts.

Re: Hard cocking and POI shift FIX!!!

Postby RayK » Thu Feb 19, 2015 8:31 am

I wish Jamie USMC Shooter were still around, but he bought a Cricket and we never heard from him again.

Ray
25 W-rod | 08 shots @ 70 FPE -2% | 3100 fill
25 M-rod | 40 shots @ 35 FPE -4% | 3100 fill
22 M-rod | 51 shots @ 25 FPE -4% | 3100 fill
17 M-rod | 50 shots @ 19 FPE -4% | 2500 fill
25 P_rod | 16 shots @ 29 FPE -3% | 2100 fill
RayK
 
Posts: 5531
Joined: Sat Jun 05, 2010 3:19 pm

Re: Hard cocking and POI shift FIX!!!

Postby wimpanzee » Wed Feb 25, 2015 2:07 pm

Forgive my ignorance, but browsing amazon for "ball hone" shows something that seems it would polish the inside of the tube nicely, but what do you use to chamfer the edges of the stamped out areas?

Can someone explain it for the mechanically challenged?
wimpanzee
 
Posts: 75
Joined: Wed Jun 25, 2014 7:41 am

Re: Hard cocking and POI shift FIX!!!

Postby Doc » Wed Feb 25, 2015 3:44 pm

Use a Dremel with a ball tool.
Doc
 
Posts: 570
Joined: Fri May 23, 2014 11:47 am
Location: Central Texas

Re: Hard cocking and POI shift FIX!!!

Postby caniborrowsomeammo » Wed Feb 25, 2015 8:14 pm

wimpanzee wrote:Forgive my ignorance, but browsing amazon for "ball hone" shows something that seems it would polish the inside of the tube nicely, but what do you use to chamfer the edges of the stamped out areas?

Can someone explain it for the mechanically challenged?


I used something like this:
http://www.amazon.com/Dremel-953-Alumin ... SCH614EYGS
caniborrowsomeammo
 
Posts: 469
Joined: Sat Jun 11, 2011 4:30 pm
Location: Santa Rosa

Re: Hard cocking and POI shift FIX!!!

Postby wimpanzee » Thu Feb 26, 2015 7:40 am

Well, that seems cheap enough. I have my rifle apart right now, awaiting some orings. I might as well try it!

Been meaning to put some graphite moly on the hammer, too. Any suggestions or comments on that?

Thanks for the info!
wimpanzee
 
Posts: 75
Joined: Wed Jun 25, 2014 7:41 am

Re: Hard cocking and POI shift FIX!!!

Postby wimpanzee » Thu Feb 26, 2015 1:17 pm

Do I need to pull the valve and everything out of the tube like Travis' video on installing the NBH, or can I get these edges trimmed down with and not worry about particles getting into the valve?
wimpanzee
 
Posts: 75
Joined: Wed Jun 25, 2014 7:41 am

Re: Hard cocking and POI shift FIX!!!

Postby Doc » Thu Feb 26, 2015 1:38 pm

I prefer to take the gun all the way down but thats just my OCD.
Doc
 
Posts: 570
Joined: Fri May 23, 2014 11:47 am
Location: Central Texas

Previous

Return to Marauder Problems and Solutions

Who is online

Users browsing this forum: No registered users and 3 guests