Howdy all,
I just opened up the new box sent by pyramydair. One big thing I noticed is that the gun rattles inside the barrel or tank, but directly underneath where the stock sling screw is located. Does anyone else have this rattle when the gun is empty?
MarauderAirRifle.com
Marauder Air Rifle Forum & Fan Site
.22 New MRod Supposed to rattle?
Forum rules
MarauderAirRifle.com is not owned, Affiliated, or controlled by Crosman.
The Scope and goal of this section of the form is provide useful information 24/7 because I realize that most of us play with the toys on weekends when big companies and telephone support is not always available.
Normally if problems occur during this window you are SOL until the next business day (and your fun is over)
So if you are having problems check or search here to see if it is a known issue and what steps can be taken to resolve the issue.
If you ask questions on this forum, I can not guarantee Crosman support will see the post or reply to it, and you may need to give them a call at 800-724-7486 if you still need help or replacement parts.
MarauderAirRifle.com is not owned, Affiliated, or controlled by Crosman.
The Scope and goal of this section of the form is provide useful information 24/7 because I realize that most of us play with the toys on weekends when big companies and telephone support is not always available.
Normally if problems occur during this window you are SOL until the next business day (and your fun is over)
So if you are having problems check or search here to see if it is a known issue and what steps can be taken to resolve the issue.
If you ask questions on this forum, I can not guarantee Crosman support will see the post or reply to it, and you may need to give them a call at 800-724-7486 if you still need help or replacement parts.
10 posts • Page 1 of 1
.22 New MRod Supposed to rattle?
by ran007 on Wed Jan 19, 2011 11:33 am
Randall
.22 Marauder, 80cf SCUBA Tank, Benjamin yoke adapter, Leapers 5th Gen 6-24x50. Pellet: H&N Baracuda Match 21.14gr, 5.51mm - 1/2" group @ 50 yards, 2400-1500psi.
.22 Marauder, 80cf SCUBA Tank, Benjamin yoke adapter, Leapers 5th Gen 6-24x50. Pellet: H&N Baracuda Match 21.14gr, 5.51mm - 1/2" group @ 50 yards, 2400-1500psi.
- ran007
- Posts: 50
- Joined: Sun Jan 16, 2011 9:37 pm
Re: .22 New MRod Supposed to rattle?
by DaveShooter on Wed Jan 19, 2011 11:42 am
Their is a little piece inside the male foster fitting will rattle when rifle has low or no air in the air tube. Put a higher fill and see if it stops.Sorry I don't know the name of that piece. I think it closes back inside the male foster fitting to keep air from escapeing. Or another thot maybe the striker inside the hammer area is rattleing- check to see if it does when or with rifle is cocked. If ya really want to know for safety issue call Crosman when in doubt.... I really don't think ya got a problem with your new rifle. Hope that helps.ran007 wrote:Howdy all,
I just opened up the new box sent by pyramydair. One big thing I noticed is that the gun rattles inside the barrel or tank, but directly underneath where the stock sling screw is located. Does anyone else have this rattle when the gun is empty?
- DaveShooter
- Posts: 185
- Joined: Sat Jun 13, 2009 9:28 pm
- Location: Ohio
Re: .22 New MRod Supposed to rattle?
by ran007 on Wed Jan 19, 2011 11:56 am
Do you think it's the check valve?
Randall
.22 Marauder, 80cf SCUBA Tank, Benjamin yoke adapter, Leapers 5th Gen 6-24x50. Pellet: H&N Baracuda Match 21.14gr, 5.51mm - 1/2" group @ 50 yards, 2400-1500psi.
.22 Marauder, 80cf SCUBA Tank, Benjamin yoke adapter, Leapers 5th Gen 6-24x50. Pellet: H&N Baracuda Match 21.14gr, 5.51mm - 1/2" group @ 50 yards, 2400-1500psi.
- ran007
- Posts: 50
- Joined: Sun Jan 16, 2011 9:37 pm
Re: .22 New MRod Supposed to rattle?
by warrior23 on Wed Jan 19, 2011 3:42 pm
My 22Mrod had a loose stock screw that made a rattling noise.
- warrior23
- Posts: 19
- Joined: Thu Jan 06, 2011 4:21 pm
Re: .22 New MRod Supposed to rattle?
by MobyMyster on Wed Jan 19, 2011 3:49 pm
Did you tighten it...?
I thought my .25 Mrod had something loose too - turned out just the baffles.
I thought my .25 Mrod had something loose too - turned out just the baffles.
MobyMyster in Kansas
- MobyMyster
- Posts: 2
- Joined: Sat Oct 30, 2010 4:44 pm
- Location: Wichita, KS USA
Re: .22 New MRod Supposed to rattle?
by Supercharged86 on Wed Jan 19, 2011 3:51 pm
ran007 wrote:Do you think it's the check valve?
Yeap, there's a check valve in the front end cap assembly. Also make sure the shroud is tight by turning it CW, but first loosen the end cap a little, then retighten it. This will also ensure the baffles are tight inside. Steve
Forum Moderator
Mrod .177 with EunJin 16.1's = A bad day!!!
Mrod .177 with EunJin 16.1's = A bad day!!!
-
Supercharged86 - Posts: 832
- Joined: Sun Nov 01, 2009 7:14 pm
- Location: Cranston, Rhode Island
Re: .22 New MRod Supposed to rattle?
by heli on Wed Jan 19, 2011 4:10 pm
My .25 rattled,I waited two weeks for a tank, filled it and it went away. It was a long two weeks waiting to find out. so I know how you feel.
GET OUT AND VOTE!
-
heli - Posts: 12
- Joined: Mon Oct 18, 2010 7:08 pm
Re: .22 New MRod Supposed to rattle?
by DaveShooter on Thu Jan 20, 2011 7:12 am
You're dead on the money Steve. I couldn't think of the parts name. Absent minded me.Supercharged86 wrote:ran007 wrote:Do you think it's the check valve?
Yeap, there's a check valve in the front end cap assembly. Also make sure the shroud is tight by turning it CW, but first loosen the end cap a little, then retighten it. This will also ensure the baffles are tight inside. Steve
- DaveShooter
- Posts: 185
- Joined: Sat Jun 13, 2009 9:28 pm
- Location: Ohio
Re: .22 New MRod Supposed to rattle?
by ran007 on Thu Jan 20, 2011 11:07 am
Yep, so I gave it a shot of air, and it must have been the check valve... no more rattle. =)
Randall
.22 Marauder, 80cf SCUBA Tank, Benjamin yoke adapter, Leapers 5th Gen 6-24x50. Pellet: H&N Baracuda Match 21.14gr, 5.51mm - 1/2" group @ 50 yards, 2400-1500psi.
.22 Marauder, 80cf SCUBA Tank, Benjamin yoke adapter, Leapers 5th Gen 6-24x50. Pellet: H&N Baracuda Match 21.14gr, 5.51mm - 1/2" group @ 50 yards, 2400-1500psi.
- ran007
- Posts: 50
- Joined: Sun Jan 16, 2011 9:37 pm
Re: .22 New MRod Supposed to rattle?
by Supercharged86 on Thu Jan 20, 2011 1:24 pm
There you go Randall, let'm rip!!!
Forum Moderator
Mrod .177 with EunJin 16.1's = A bad day!!!
Mrod .177 with EunJin 16.1's = A bad day!!!
-
Supercharged86 - Posts: 832
- Joined: Sun Nov 01, 2009 7:14 pm
- Location: Cranston, Rhode Island
10 posts • Page 1 of 1
Return to Marauder Problems and Solutions
Who is online
Users browsing this forum: No registered users and 1 guest
