Straight clip magazine for marauder?

3rd Party Stocks, Barrels, Regulators, air tube extensions, etc. and where to find them.

Straight clip magazine for marauder?

Postby robble » Tue Dec 16, 2014 8:40 pm

****notice: there hasn't been a straight clip solution discovered and topic goes off course. Read if you like but don't expect to find a straight clip here. If that changes I will change the notice *****

As I'm sure everyone knows a magazine sticks above the breach making you have to use high risers for the scope to clear it.

The other thing most of us know is that the closer the scope is to the barrel more accurate it is at short range. I happen to be one of those people who shoot at very short ranges, say 5 feet to 20 feet while hunting rats in my yard
At ranges that short the high-rise really causes extreme differences in the vertical point of impact even with as little as two or 3 feet of range difference.

I know there is a single shot solution but I don"t want to give up the ability to quickly shoot again with the magazine.

Has anyone made a straight clip that just sticks out the side instead of the circular one that sticks above the breach? I can easily envision how it would work but I do not have the tools to create it. I would be very happy if I could lower the scoop about 15 mm.
Last edited by robble on Sat Dec 20, 2014 10:51 am, edited 1 time in total.
robble
 
Posts: 34
Joined: Sat Oct 18, 2014 5:51 am

Re: Straight clip magazine for marauder?

Postby SHOOTINIT » Wed Dec 17, 2014 8:56 am

ARE YOU USING A MILDOT SCOPE?
99% of the time it's the shooter, not the gun.

SHOOTINIT
 
Posts: 1918
Joined: Thu Apr 18, 2013 10:13 am

Re: Straight clip magazine for marauder?

Postby robble » Wed Dec 17, 2014 2:49 pm

Unless I can get good at estimating ranges within 1 foot or there is som trick I don't know about then the mil dots don't do me much good. Between the 5-30 feet I'm usually shooting at there is a 4-5 dot seperation. Rarely, I might shoot as far as -45'. The rats are large but they aren't so large that I can afford to be a couple inches too high or low.

I also shoot with a little .177 umarex fusion. The scope is much lower on there and I have no problem nailing a rats head from 5-30' with very little variation from zero in the scope.

One thing I thought of trying is to zero the scope out at the maximum range I shoot at in stead of the more common closer ranges. Then for closer ranges I'd only be dealing with the dots below zero. As it is now I zero forabot 20'. At ranges closer than that I'm below zero but further out I'm using dots able zero.

Still, getting the scope closer to the barrel will make it much easier I would still like a flat clip.
robble
 
Posts: 34
Joined: Sat Oct 18, 2014 5:51 am

Re: Straight clip magazine for marauder?

Postby Bob La Londe » Wed Dec 17, 2014 3:24 pm

It might be possible to make a holder for something like the manually fed five shot clip used with the Crosman 760. I do not think a typical stacked spring magazine is going to work with soft lead pellets.

An actual spring fed flat magazine does not to my knowledge exist, but you can always go to a single shot tray like this: http://www.pyramydair.com/search-result ... 1&saSearch

I can visualize a pellet carrier type flat magazine using a constant force coil spring that draws the carrier over, and a horizontal carrier instead of a circular carrier, but I don't think there is enough demand for it to try and make one. It would be complicated and quite wide needing to be slight more than twice the width overall as the number of pellets it is designed for. Atleast when loaded.

Using a lower scope mount has its issues as well. It limits the optical size of the scope you can use.
CNC Molds N Stuff
http://www.cncmolds.com

.177 XSB50
.177 Srod Reg-Extnsn-Prt .1405
.25 Srod Sprg & Hmr
.22 Hatsan 155
.177 NP BLECH!
.177 Metal Daisy 880
.177 Plastic Daisy 880
.177 Crosman 760 Plastic Alu Spring Guide
.22 Crosman Model 1
Bob La Londe
 
Posts: 177
Joined: Sat Oct 18, 2014 7:07 pm
Location: Arizona

Re: Straight clip magazine for marauder?

Postby robble » Wed Dec 17, 2014 4:11 pm

Your idea is close to what I'm envisioning. Even if it held just 3 pellets it would allow for a couple fast follow up shots.
At the range I'm looking at I don't need a large scope.
IF I had access to a router, drill press, and table saw I could make one out of wood fairly easily. The indexing would be the tricky part.
robble
 
Posts: 34
Joined: Sat Oct 18, 2014 5:51 am

Re: Straight clip magazine for marauder?

Postby SHOOTINIT » Wed Dec 17, 2014 6:50 pm

anything is possible
99% of the time it's the shooter, not the gun.

SHOOTINIT
 
Posts: 1918
Joined: Thu Apr 18, 2013 10:13 am

Re: Straight clip magazine for marauder?

Postby Bob La Londe » Wed Dec 17, 2014 7:23 pm

SHOOTINIT wrote:anything is possible


Ha! After mentioning it I can't stop thinking about different ways I would build it.
CNC Molds N Stuff
http://www.cncmolds.com

.177 XSB50
.177 Srod Reg-Extnsn-Prt .1405
.25 Srod Sprg & Hmr
.22 Hatsan 155
.177 NP BLECH!
.177 Metal Daisy 880
.177 Plastic Daisy 880
.177 Crosman 760 Plastic Alu Spring Guide
.22 Crosman Model 1
Bob La Londe
 
Posts: 177
Joined: Sat Oct 18, 2014 7:07 pm
Location: Arizona

Re: Straight clip magazine for marauder?

Postby caniborrowsomeammo » Wed Dec 17, 2014 8:11 pm

Ever think of trying a holographic sight? http://www.amazon.com/Eotech-Holographi ... B0022SI1A4
Little expensive though. :o

Or a red dot? http://www.amazon.com/Truglo-Red-Dot-Co ... +dot+sight
Probably easier on the pocketbook. :)

Or the CenterPoint that comes with the Woods Walker. I have 2 I never used.

Had a red dot on my FDPCP for awhile (UTG). Personally still prefer irons at close range. But we don't have many options with the Rods.
caniborrowsomeammo
 
Posts: 392
Joined: Sat Jun 11, 2011 4:30 pm
Location: Santa Rosa

Re: Straight clip magazine for marauder?

Postby Bob La Londe » Wed Dec 17, 2014 8:41 pm

I seem to recall my uncle saying he had good luck using a laser sight for barn rats. He'll be here for Christmas. I'll ask him about it.
CNC Molds N Stuff
http://www.cncmolds.com

.177 XSB50
.177 Srod Reg-Extnsn-Prt .1405
.25 Srod Sprg & Hmr
.22 Hatsan 155
.177 NP BLECH!
.177 Metal Daisy 880
.177 Plastic Daisy 880
.177 Crosman 760 Plastic Alu Spring Guide
.22 Crosman Model 1
Bob La Londe
 
Posts: 177
Joined: Sat Oct 18, 2014 7:07 pm
Location: Arizona

Re: Straight clip magazine for marauder?

Postby robble » Wed Dec 17, 2014 8:43 pm

caniborrowsomeammo wrote:Ever think of trying a holographic sight? http://www.amazon.com/Eotech-Holographi ... B0022SI1A4
Little expensive though. :o

Or a red dot? http://www.amazon.com/Truglo-Red-Dot-Co ... +dot+sight
Probably easier on the pocketbook. :)

Or the CenterPoint that comes with the Woods Walker. I have 2 I never used.

Had a red dot on my FDPCP for awhile (UTG). Personally still prefer irons at close range. But we don't have many options with the Rods.


I've never looked through a red dot or holographic and have no idea what they'd be like. I assume they'd still be affected by being up high. Iron sites would work great – if the magazine was not in the way
robble
 
Posts: 34
Joined: Sat Oct 18, 2014 5:51 am

Next

Return to Marauder Aftermarket Parts and Accessories

Who is online

Users browsing this forum: No registered users and 1 guest