Help support the forum and get %15 Off the Marauder and Accessories direct from Crosman using the coupon code MROD4RUM by CLICKING HERE
|
If you think the built in forum search function sucks, Use Googles site search below
|
BENJAMIN MARAUDER 5.5 REGULATED - By Artilheiro
23 posts
• Page 3 of 3 • 1, 2, 3
Re: BENJAMIN MARAUDER 5.5 REGULATED - By Artilheiro
by Artilheiro » Thu Jul 07, 2011 8:15 am
RatRacer, thank's for having translated the post.
-
Artilheiro - Posts: 54
- Joined: Fri Dec 04, 2009 9:17 am
Re: BENJAMIN MARAUDER 5.5 REGULATED - By Artilheiro
by RatRacer » Thu Jul 07, 2011 9:52 am
De Nada! 
Benjamin Marauder .22 pistol, carbined- 18FPE
Benjamin Discovery .22 Multi-Shot, Hawke AirMax 4-12 X 40 AO/IR
CS 2400KT .22, BB 3-9 X32 AO/IR
Benjamin Discovery .22 Multi-Shot, Hawke AirMax 4-12 X 40 AO/IR
CS 2400KT .22, BB 3-9 X32 AO/IR
-
RatRacer - Posts: 584
- Joined: Wed Jun 15, 2011 11:41 am
- Location: Steve in S.W. Florida
Re: BENJAMIN MARAUDER 5.5 REGULATED - By Artilheiro
by Artilheiro » Mon Jul 11, 2011 7:48 am
Project Marauder
Taking as its basis the first 51, BAM50 and tunadas by master Paulo Martins (who manages this project Marauder) and, in order to maintain the original design, we will not use the cylinder HPA. The body of the valve is machined from 28 mm to 26.7 mm (inner diameter cylinder Mrod). The "holes" for the manometer, disk burst, and quick fill, are buffered with screws allem without head and machined. The Mrod, is already prepared for 268m shots with Heavy i/o for JSB, 1gr of 18, with a pressure of 1800PSI. The valve with 1800PSI output, has already been bought by Adilson, and should arrive until mid-May. It is clear that in theory, it works. However, in practice it certainly will take several other adjustments that the master logs Paulo Martins. On grounds of non use of the cylinder HPA, their autonomy of shooting will be reduced. That is, by the type of evidence that dispute, if she der uns 30 shots good, we are already satisfied. Therefore, we will soon have the Mrod governed and with original design. Ha, this project can be perfectly used also in S-410, someone in danger?
The Mestre Paulo Martins found interesting! And you, what do you think of the idea?
Following are some pictures of the details of how was Mrod, after installation of the valve JDS. [b]
.
THE DISMOUNTED SET
ASSEMBLY MOUNTED
Detail of support where are the original gauge (1700 PSI output) and the body of the valve JDS
PRESSURE GAUGES IN THE BODY OF THE GUN.
The original gauge (white background), marks the valve pressure shot-1800PSI. The second (black background) marks the pressure within the barrel of the gun-3000PSI
PRESSURE GAUGES IN THE BUTTSTOCK.
The original on the left. Right, what the master Paulo Martins made in hand with the Dremel
SET
BREECH BOLT
New FORE-END.
The grip has improved a lot with this template
New PILOTINHO
The values below, were obtained by the master himself Paulo Martins, he performed tests.
For the week, I intend to post photos of groupings
Taking as its basis the first 51, BAM50 and tunadas by master Paulo Martins (who manages this project Marauder) and, in order to maintain the original design, we will not use the cylinder HPA. The body of the valve is machined from 28 mm to 26.7 mm (inner diameter cylinder Mrod). The "holes" for the manometer, disk burst, and quick fill, are buffered with screws allem without head and machined. The Mrod, is already prepared for 268m shots with Heavy i/o for JSB, 1gr of 18, with a pressure of 1800PSI. The valve with 1800PSI output, has already been bought by Adilson, and should arrive until mid-May. It is clear that in theory, it works. However, in practice it certainly will take several other adjustments that the master logs Paulo Martins. On grounds of non use of the cylinder HPA, their autonomy of shooting will be reduced. That is, by the type of evidence that dispute, if she der uns 30 shots good, we are already satisfied. Therefore, we will soon have the Mrod governed and with original design. Ha, this project can be perfectly used also in S-410, someone in danger?
The Mestre Paulo Martins found interesting! And you, what do you think of the idea?
Following are some pictures of the details of how was Mrod, after installation of the valve JDS. [b]
.
THE DISMOUNTED SET
ASSEMBLY MOUNTED
Detail of support where are the original gauge (1700 PSI output) and the body of the valve JDS
PRESSURE GAUGES IN THE BODY OF THE GUN.
The original gauge (white background), marks the valve pressure shot-1800PSI. The second (black background) marks the pressure within the barrel of the gun-3000PSI
PRESSURE GAUGES IN THE BUTTSTOCK.
The original on the left. Right, what the master Paulo Martins made in hand with the Dremel
SET
BREECH BOLT
New FORE-END.
The grip has improved a lot with this template
New PILOTINHO
The values below, were obtained by the master himself Paulo Martins, he performed tests.
For the week, I intend to post photos of groupings
-
Artilheiro - Posts: 54
- Joined: Fri Dec 04, 2009 9:17 am
23 posts
• Page 3 of 3 • 1, 2, 3
Who is online
Users browsing this forum: No registered users and 1 guest
